Payment & Shipping Terms:
|Machine Weight:||About 5950Kgs||Max Positioning Speed:||140m/min|
|Repeated Positioning Accuracy Of X, Y And Z Axles:||±0.02 Mm||Power Requirement:||380V,50/60Hz|
|Air Compressor & Cold-dryer:||Atlas Copco||Effective Cutting:||3000* 1500mm|
High Power Metal Laser Cutting Machine , Fiber Cutter Machine Can Cut Doors And Windows
GS-LFDS3015 fiber laser cutting machine using a domestic dust removal system
Widely used for metal-sheet fabrication:
Widely used for metal-sheet processing,advertising trademark, advertising character, high/low voltage electrical cabinet, mechanism parts, kitchenware, cars, mechanical, metal craftwork, saw blade, electronic parts, eye-glasses, spring, circuit board, kettle,medical microelectronics, hardware, knives tool, measurement, instrument,etc.
Laser cutting is most widely used of laser processing industry. GS-LFDS3015 laser cutting machine adopts High-power and high-performance laser source with international advanced technology, CNC system, imported AC servo motor, High-precision gear rack and imported high-precision linear guide. It is stable, high-performance, strong-load. It is a high-tech product with laser cutting, precision machine and CNC. It has the characteristics of high speed, precision, high efficiency, good cost performance and so on.
Before using GS-LFDS 3015 laser cutting machine, please be sure to read this Instruction Manual in detail.
|Laser source medium||Fiber|
|Cutting range(L*W)||3000mm × 1500mm||3000mm × 1500mm||3000mm × 1500mm|
|Z axle stroke||150 mm|
|Max cutting speed||40m/min||42m/min||45m/min|
|Max positioning speed||140m/min|
|Wok platform size/Max height of feeding material||4250x2500mm/more than 120mm|
|Cooling form||water cooling|
|Output power of laser source||1000W (imported)||1500W (imported)||2000W (imported)|
|Min. cutting gap||≤0.1mm||≤0.125mm||≤0.125mm|
|Positioning accuracy of X, Y and Z axles||±0.03 mm|
|Repeated positioning accuracy of X, Y and Z axles||±0.02 mm|
|Thickness of cutting material
(according to material)
|Drive model||Imported servo motor|
|Continuous working time||24 Hours|
|Machine weight||About 5950Kgs|
|Outer dimension||7828mm x 3741mm x 1940mm|
|Total protection level of power supply||IP54|
1.Power supply power supply specification: three phase five wire system, 50Hz 380V, three phase unbalance <2.5%, line voltage fluctuation <5%.
2.Protective grounding: the ground resistance of the machine tool is <4.
3.Good ventilation condition, no dust, no corrosion, no pollution and no conductive dust.
4.No shocking around the machine, and dug earthquake proof trench around the bed.
5.The laser must be installed at 20℃ ambient temperature (to prevent condensation), more than 1 meters above the surrounding for the maintenance channel.
6.Operating table in the front of the machine bed, electrical control cabinet on the left side of the machine bed, the distance from the wall should be greater than 1.5M.
7.In order to prevent fire, a certain number of fire extinguishers should be configured in the workplace. Fire passage reserved for more than 1 meters wide
Laser cutting machine safety operation procedures
1, abide by common cutting machine safety operation procedures.In strict accordance with the laser launcher to start the laser, dimmer, commissioning.
2, the operator must be trained and familiar with cutting software, equipment structure, performance, and master the knowledge about operating system.
3, wear labor protection articles according to the rules in the vicinity of a laser beam must wear protective glasses in keeping with the rules.
4, in ascertain whether a particular material can use laser or cut before, not to its processing, in order to avoid potential danger of smoke and steam.
5, the operator shall not leave the job or when the device is alone.so escrow, if indeed need should be shut down or cut off the power switch when they leave.
Laser cutting machine sample